Fleming Right Hand Rule:
As per Faraday’s law of electromagnetic induction, whenever a conductor moves inside a magnetic field, there will be an induced current in it. If this conductor is forcefully moved inside the magnetic field, there will be a relation between the direction of applied force, magnetic field and the electric current. This relation among these three directions, is determined by by Fleming Right Hand Rule
An operational amplifier (op-amp) is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op-amp produces an output potential (relative to circuit ground) that is typically hundreds of thousands of times larger than the potential difference between its input terminals.
A proportional-integral-derivative controller (PID controller) is a generic control loop feedback mechanism (controller) widely used in industrial control systems. A PID controller calculates an "error" value as the difference between a measured process variable and a desired setpoint. The controller attempts to minimize the error by adjusting the process control inputs.
A DC motor is a mechanically commutated electric moto powered from direct current (DC). The stator is stationary in space by definition and therefore the current in the rotor is switched by the commutator to also be stationary in space. This is how the relative angle between the stator and rotor magnetic flux is maintained near 90 degrees, which generates the maximum torque.
An induction or asynchronous motor is an AC motor in which current is induced in the rotor winding by the magnetic field of the stator winding, by electromagnetic induction.
An infrared sensor is an electronic device that emits and/or detects infrared radiation in order to sense some aspect of its surroundings. Infrared sensors can measure the heat of an object, as well as detect motion.
The media controlled by the solenoid valve enters the valve through the inlet port (Part 2 in the illustration above). The media must flow through the orifice (9) before continuing into the outlet port (3). The orifice is closed and opened by the plunger (7).
The valve pictured above is a normally-closed solenoid valve. Normally-closed valves use a spring (8) which presses the plunger tip against the opening of the orifice. The sealing material at the tip of the plunger keeps the media from entering the orifice, until the plunger is lifted up by an electromagnetic field created by the coil.
1. Valve Body
4. Coil / Solenoid
7. Plunger
2. Inlet Port
5. Coil Windings
8. Spring
3. Outlet Port
6. Lead Wires
9. Orifice
Reverse osmosis (RO) is a water purification technology that uses a semipermeable membrane. This membrane-technology is not properly a filtration method. In RO, an applied pressure is used to overcome osmotic pressure, a colligative property, that is driven by chemical potential, a thermodynamic parameter. RO can remove many types of molecules and ions from solutions and is used in both industrial processes and in producing potable water. The result is that the solute is retained on the pressurized side of the membrane and the pure solvent is allowed to pass to the other side. To be "selective," this membrane should not allow large molecules or ions through the pores (holes), but should allow smaller components of the solution (such as the solvent) to pass freely.
Level sensors detect the level of substances that flow, including liquids, slurries, granular materials, and powders. Fluids and fluidized solids flow to become essentially level in their containers (or other physical boundaries) because of gravity whereas most bulk solids pile at an angle of repose to a peak. The substance to be measured can be inside a container or can be in its natural form (e.g., a river or a lake).
The insulated-gate bipolar transistor or IGBT is a three-terminal power semiconductor device primarily used as an electronic switch and in newer devices is noted for combining high efficiency and fast switching. It switches electric power in many modern appliances: Variable-Frequency Drives (VFDs), electric cars, trains, variable speed refrigerators, air-conditioners.
How a clamp meter works:
In electrical and electronic engineering, a current clamp or current probe is an electrical device having two jaws which open to allow clamping around an electrical conductor. This allows properties of the electric current in the conductor to be measured, without having to make physical contact with it, or to disconnect it for insertion through the probe. Current clamps are usually used to read the magnitude of asinusoidal current (as invariably used in alternating current (AC) power distribution systems), but in conjunction with more advanced instrumentation the phase and waveform are available. Very high alternating currents (1000 A and more) are easily read with an appropriate meter; direct currents, and very low AC currents (milliamperes) are more difficult to measure.
A CURRENT TRANSFORMER (CT) is used for measurement of alternating electric currents. Current transformers, together with voltage transformers (VT) (potential transformers (PT)), are known as instrument transformers. When current in a circuit is too high to directly apply to measuring instruments, a current transformer produces a reduced current accurately proportional to the current in the circuit, which can be conveniently connected to measuring and recording instruments. A current transformer also isolates the measuring instruments from what may be very high voltage in the monitored circuit. Current transformers are commonly used in metering and protective relays in the electrical power industry.
In electronics, an opto-isolator, also called an optocoupler, photocoupler, or optical isolator, is a component that transfers electrical signals between two isolated circuits by using light. Opto-isolators prevent high voltages from affecting the system receiving the signal.
A diode is an electronic device which allows current to pass through in
one direction but not in the other. It is commonly used in another device call a bridge rectifier which is used to convert alternating current into direct current.
A pressure transmitter is a pressure sensor, typically for gases or liquids. This pressure sensing device has current output. It can also be defined as an analogue device that produces a charge in voltage or current when the internal pressure changes state.
A thyristor is a four-layer semiconductor that is often used for handling large amounts of power. While a thyristor can be turned on or off, it can also regulate power using something called phase angle control. This allows the amount of power output to be controlled by adjusting the angle of the current input. An example of this is the a dimmer switch for a light.
